ShaneJ
Field Bee
 Offline
Gender: 
Posts: 511
Location: Burpengary, Queensland, Australia.
|
 |
« Reply #60 on: March 17, 2012, 11:07:56 AM » |
|
I'm pretty sure it does. Even allowing for a 4mm blade, all will fit on the sheet.
|
|
|
|
|
Logged
|
Shane
|
|
|
Robo
Technical
Administrator
Galactic Bee
Offline
Gender:
Posts: 6169
Location: Scenic Catskill Mountains - NY
Beekeep On!
|
|
« Reply #61 on: March 17, 2012, 06:35:56 PM » |
|
Shane,
Attached is the original cut list in metric.
|
|
|
|
« Last Edit: March 18, 2012, 08:12:00 AM by Robo »
|
Logged
|
|
|
|
ShaneJ
Field Bee
Offline
Gender:
Posts: 511
Location: Burpengary, Queensland, Australia.
|
|
« Reply #62 on: March 17, 2012, 07:55:31 PM » |
|
Ahh, thank you mate. Your measurements are pretty much right on what I got. I rounded my numbers though to make the job a tad easier.
What version of edition of Sheet Layout do you use? I'm just using the free version at the moment, but I cant get it to print out like what you attached.
|
|
|
|
|
Logged
|
Shane
|
|
|
Robo
Technical
Administrator
Galactic Bee
Offline
Gender:
Posts: 6169
Location: Scenic Catskill Mountains - NY
Beekeep On!
|
|
« Reply #63 on: March 18, 2012, 08:12:53 AM » |
|
Shane,
I don't use sheet layout. It is cut list.
|
|
|
|
|
Logged
|
|
|
|
ShaneJ
Field Bee
Offline
Gender:
Posts: 511
Location: Burpengary, Queensland, Australia.
|
|
« Reply #64 on: March 18, 2012, 05:09:12 PM » |
|
Thanks mate.
|
|
|
|
|
Logged
|
Shane
|
|
|
samsungpizza
New Bee
Offline
Gender:
Posts: 26
Location: Emporium, Pa. 15834
|
|
« Reply #65 on: April 02, 2012, 10:16:58 AM » |
|
I made a few of these last night. I Opted for 1" dia. holes toward the top for entrance, and did the same for back side and screened over for ventilation. Also cut 2 3/4" hole, screened, for top feeder. Nice design, and cheap. Thanks!
|
|
|
|
|
Logged
|
|
|
|
weldingfreak6010
New Bee
Offline
Gender:
Posts: 14
Location: Centerville, iowa
|
|
« Reply #66 on: April 06, 2013, 11:25:27 PM » |
|
I hope this was not covered but is there any changes to the box to make it into a super size dimension wise. ( I know I do not put the bottom on it or need the top.) Is the bee space going to be ok between the top of the bottom frames and the bottom of the top frames, if you understand what I am getting at here. thanks guys, and Coates thanks for the design
|
|
|
|
|
Logged
|
|
|
|
bailey
Field Bee
Offline
Gender:
Posts: 823
Location: RACELAND LA
|
|
« Reply #67 on: April 07, 2013, 12:49:42 PM » |
|
If your going to make a super put a 2" strip on the bottom like you do on the top. It makes all sides and tops and bottom match up.
Make the box. Then put it on the nuc. You will see why you need the strip.
Bailey
|
|
|
|
|
Logged
|
most often i find my greatest source of stress to be OPS ( other peoples stupidity )
It is better to keep ones mouth shut and be thought of as a fool than to open ones mouth and in so doing remove all doubt.
|
|
|
weldingfreak6010
New Bee
Offline
Gender:
Posts: 14
Location: Centerville, iowa
|
|
« Reply #68 on: April 07, 2013, 07:46:49 PM » |
|
If your going to make a super put a 2" strip on the bottom like you do on the top. It makes all sides and tops and bottom match up.
Make the box. Then put it on the nuc. You will see why you need the strip.
Bailey
Thanks I was wondering about that bottom , thanks again |
|
|
|
|
Logged
|
|
|
|
BAH
New Bee
Offline
Gender:
Posts: 17
Location: Crossvile, TN
|
|
« Reply #69 on: May 19, 2013, 05:48:17 PM » |
|
Thank you, a must make project!
|
|
|
|
|
Logged
|
|
|
|
|
